Compatible Systems RISC Router 3000e Manuel d'utilisateur Page 117
- Page / 119
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Jumper Settings Appendix A-1
Appendix A
Jumper Settings
The EcoLAN 3000E will automatically configure the network configuration without
the need to access internal jumpers. However, in some cases it may be necessary to
use a jumper to reset the 3000E back to a factory default condition.
HANDLING PRECAUTIONS
FOR
STATIC SENSITIVE DEVICES
The EcoLAN 3000E is normally contained within the printer which acts to protect sensi-
tive components from damage due to electrostatic discharge (ESD) during normal opera-
tion. When performing installation procedures, however, take proper static control
precautions to prevent damage to equipment.
WARNING: Make sure you do not have the printer plugged into a wall outlet. If it is,
unplug the power cord BEFORE you open the unit. Remove the 3000E
from the printer (refer to Chapter 2 installation instructions if necessary).
A.1 Reset the EcoLAN 3000E to Factory Default Settings
When the management utilities cannot be used to perform a reset to factory defaults,
the EcoLAN 3000E may be restored to factory default conditions with a jumper
(OP2). The function of OP2 is to reconfigure NVRAM. This is done when a unit is
moved from one site to another and should be restored to as as-new condition.
Use the diagram and instructions on the following page to reset the 3000E to factory
defaults with OP2.
Cover-Preface.book Page 1 Wednesday, May 12, 1999 10:48 PM
- Kyocera EcoLAN 3000E 1
- Thank You 2
- Copyright Notice 2
- Trademarks 2
- FCC Notice: 2
- Table of Contents 3
- Table of Contents iv 4
- Table of Contents v 5
- Table of Contents vi 6
- Table of Contents vii 7
- Appendix A Jumper Settings 8
- Appendix B Specifications 8
- Introduction 9
- 1.1 What’s in Your Package 10
- 1.2 Hardware/NOSRequirements 11
- Hardware Installation 12
- Hardware Installation 2-2 13
- Hardware Installation 2-3 14
- Hardware Installation 2-4 15
- Browser Based Management 16
- 3.1.2 Using MAP 17
- 3.1.3 Extensive On-Line Help 17
- 3.2.2 Extensive On-Line Help 18
- Browser Based Management 3-4 19
- Browser Based Management 3-5 20
- NetWare Configuration 21
- 4.1.2 Create Print Queues 22
- NetWare Configuration 4-3 23
- NetWare Configuration 4-4 24
- NetWare Configuration 4-5 25
- (Optional) 26
- 4.1.8 Primary File Server 27
- NetWare Configuration 4-8 28
- 4.2.1 Confirm Bindery Context 29
- NetWare Configuration 4-10 30
- NetWare Configuration 4-11 31
- Directory Services 32
- 4.3.1 Create Printer Object 33
- NetWare Configuration 4-14 34
- NetWare Configuration 4-15 35
- 4.3.4 Assign Printer Object 36
- NetWare Configuration 4-17 37
- NetWare Configuration 4-18 38
- 4.3.6 Check Assignments 39
- (power cycle) the printer 40
- NetWare Configuration 4-21 41
- NetWare Configuration 4-22 42
- 4.5.2 Changing Print Queues 43
- 4.5.3 How to Set Up Notify 44
- Windows Configuration 45
- Windows Configuration 5-2 46
- 5.2 Windows 3.1 47
- Loading the LPR Spooler 48
- 5.4 Windows 95 and Windows 98 49
- Windows Configuration 5-6 50
- Windows Configuration 5-7 51
- Windows Configuration 5-8 52
- IPX Protocol Notes 53
- Windows Configuration 5-10 54
- Windows Configuration 5-11 55
- Windows Configuration 5-12 56
- Windows Configuration 5-13 57
- 5.5 Windows NT 3.51 58
- Windows Configuration 5-15 59
- 5.6 Windows NT 4.0 60
- Windows Configuration 5-17 61
- Windows Configuration 5-18 62
- Windows Configuration 5-19 63
- Using the Bootp Lite Utility 64
- Windows Configuration 5-21 65
- Windows Configuration 5-22 66
- Macintosh Configuration 67
- Macintosh Configuration 6-2 68
- 6.4 Using KyoManage 69
- Macintosh Configuration 6-4 70
- UNIX Configuration 71
- UNIX Configuration 7-2 72
- 7.2.1 Using BOOTP 73
- UNIX Configuration 7-4 74
- 7.2.2 Using 75
- 7.2.3 Using 75
- UNIX Configuration 7-6 76
- UNIX Configuration 7-7 77
- UNIX Configuration 7-8 78
- UNIX Configuration 7-9 79
- Printer 80
- UNIX Configuration 7-11 81
- UNIX Configuration 7-12 82
- 7.4 Host-based lpd Printing 83
- UNIX Configuration 7-14 84
- UNIX Configuration 7-15 85
- UNIX Configuration 7-16 86
- UNIX Configuration 7-17 87
- UNIX Configuration 7-18 88
- V Rel. 4 386-based Machine 89
- UNIX Configuration 7-20 90
- UNIX Configuration 7-21 91
- UNIX Configuration 7-22 92
- UNIX Configuration 7-23 93
- 7.4.9.2AIX Print Commands 94
- (non-WINS DHCP setup) 97
- 8.2.2 IP Address Persistence 98
- 8.2.3 Disabling DHCP 98
- 8.4 Telnet 100
- 8.4.1 Making the Connection 101
- 8.4.2 Configure IP Parameters 101
- The Configuration Utility 102
- Unit Serial no. 221963 102
- 8.4.6 Change Password 104
- 8.4.7 Exit 105
- 8.5 FTP Printing 106
- 8.5.3 Drag and Drop Method 107
- 8.5.4 FTP Client 107
- 9.1 LED Status Indicator 108
- EcoLAN 3000E 110
- Network Status Page 110
- 9.4 How to Diagnose Problems 111
- 9.6 Troubleshooting NetWare 113
- 9.6.3 Workstation Checklist 114
- 9.7 Troubleshooting AppleTalk 116
- Appendix A 117
- Jumper Settings Appendix A-2 118
- Appendix B 119
© 2020, manymanuals.fr. Tous droits réservés | 0.096 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels